separatore

| Wheels Dept. | Italiano Italiano | Français Français | Español Español | Deutsch Deutsch | Portugues Português | Español Pусский |

separatore

Welding & Cutting / Products / Standrd industrial line / TIG DC INVERTER / Product overview - Art 551

WIN TIG DC 180 M

Product overview - Technical data - Full-sized image - Accessories - Documentation .pdf - Comparison table

Art. 264 Cebora

WIN TIG DC 180 M (art. 551) is a single-phase inverter power source (180A 35%), suitable for TIG and MMA/-SMAW welding, with the exception of AWS6010 cellulosic electrodes; mainly designed on purpose for maintenance and repair works, as well as small production batches.

The welding machine is characterized by a black-colored casing (Special black edition).

The welding current can be adjusted from 5 to 180A and two potentiometers allow respectively the slope down and the post-gas function adjustment.

In TIG mode, the arc is started either on high frequency or by contact through the Cebora lift-system.
It features a 2 stage/4 stage selection key.

It is set up for remote control via foot control (art. 193), standard remote control (art.187+1192) or updown control on the torch (art. 1262).

The protection gases to be used are argon, argon/helium, argon/hydrogen.

It is also possible to memorize up to 9 welding programs (JOB).

Compliance with EN 61000-3-12 ensures a significant reduction in energy consumption and a wide tolerance on supply voltage (+15%/ -20%).

The power source can be powered by adequately powered motor-generators (Min. 8 KVA).

<< Top of page

separatore

Comparison table of the different power source features

Category: TIG welding power sources

= standard           = optional

Feature Power source part number
265 360
362
365 363
373
394
395
396
551 558

Max. pulse frequency 2.5 kHz

       
Max. pulse frequency 500 Hz        

High Frequency ignition

"Lift by Cebora" ignition

Spot welding mode

   
2 times / 4 times mode
3 level mode        
2 level and 4 time mode    
Minimum current in AC TIG 5 A n.a. n.a. n.a. n.a.

Max. AC frequency 150 Hz

n.a. n.a. n.a.   n.a.

Max. AC frequency 200 Hz

n.a. n.a.   n.a. n.a.  
Crater current adjustment        
Wave form selection n.a. n.a. n.a. n.a.  
AC horizontal balance n.a. n.a. n.a. n.a.

AC vertical balance (AAd)

n.a. n.a.   n.a. n.a.  

Remote control

Synergic parameters

         
Slope up adjustment  
Slope down adjustment
Pre-gas adjustment    
Post-gas adjustment
Load controlled fan        
Job mode    
Interface for cooling unit      
Ready for automatic Plasma Welding console          
Ready for manual Plasma Welding console            
Interface for TIG Hot / Cold Wire feeder          
Ready for interfacing with robot via either analog or fieldbus          
TIG MIX process n.a. n.a.   n.a. n.a.  
EVO Start (ESt) adjustment          
HF ignition by "EVO Lift" (ELF)          
Panel locking          
Digital gas control          
Quality Control function          
DC MMA welding
AC MMA welding       n.a.    
"Arc Force" function in MMA welding
"Hot Start" current
USB interface          
RS-232 interface          
LAN interface            
Possibility to update the software        
Conformity with EN61000-3-12 (PFC)
Suitable for use in environments with increased hazard of electric shock
IP23S protection class
The power source can be powered by motor generators of adequate power
Single phase power supply 230V +15% / -20%        
Three-phase power supply 400V ±10%          
Multivoltage single phase power supply 115 - 230V +15% / -20%            
Multivoltage three-phase power supply 208-220-230-400-440V ±10%            
Multivoltage three-phase power supply (200) - 220 - 440 - 480V ±10%          

 

<< top of page